Full control over your Replica – perfect settings for every action
Fully programmable fire modes – at each selector position (except “safe”), you can set semi-automatic, burst, or full-automatic fire independently of the other positions.
Active brake – Stops the motor after each shot, preventing “whipping” of the spring, and in the case of faster replicas – does not allow overspin (double shot instead of single).
Precocking – A quick response to a trigger press can make the difference between winning and losing, especially during indoor battles. When precocking is enabled, the piston remains in the rear position after each shot, allowing the shot to be fired immediately when the trigger is pulled. To release the spring after using precocking, pull and hold the trigger for 2 seconds. A second shot will be fired after 3 seconds, with no precocking and fully braked.
Rate of fire reduction – reduce the rate of fire in automatic or burst mode to save ammunition or increase realism.
Security
Discharged battery alarm – Designed for Li-Po and Li-Ion batteries. If the battery voltage drops to a dangerously low level, the user will be notified by short audible signals repeated every minute.
Diagnostic system – Constantly checks the condition of the electronics and the replica. In the event of a problem, it will immediately provide information about the possible cause, making troubleshooting easier.
Electronic fuse – protects the replica and the battery in the event of a serious malfunction. It will automatically disconnect the battery if a short circuit is detected or if a jam occurs in the gearbox.
Easy to change settings
Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. The chip communicates with the user via beeps and a multicolored LED. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.
Perun for Krytac Kriss Vector works without problems with any battery from 7V do 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.
Perun ETU MOSFET for Kriss Vector
- Brand: Perun
- Product Code: 2132
- Availability: 2
-
$170.00
Full control over your Replica – perfect settings for every action
Fully programmable fire modes – at each selector position (except “safe”), you can set semi-automatic, burst, or full-automatic fire independently of the other positions.
Active brake – Stops the motor after each shot, preventing “whipping” of the spring, and in the case of faster replicas – does not allow overspin (double shot instead of single).
Precocking – A quick response to a trigger press can make the difference between winning and losing, especially during indoor battles. When precocking is enabled, the piston remains in the rear position after each shot, allowing the shot to be fired immediately when the trigger is pulled. To release the spring after using precocking, pull and hold the trigger for 2 seconds. A second shot will be fired after 3 seconds, with no precocking and fully braked.
Rate of fire reduction – reduce the rate of fire in automatic or burst mode to save ammunition or increase realism.
Security
Discharged battery alarm – Designed for Li-Po and Li-Ion batteries. If the battery voltage drops to a dangerously low level, the user will be notified by short audible signals repeated every minute.
Diagnostic system – Constantly checks the condition of the electronics and the replica. In the event of a problem, it will immediately provide information about the possible cause, making troubleshooting easier.
Electronic fuse – protects the replica and the battery in the event of a serious malfunction. It will automatically disconnect the battery if a short circuit is detected or if a jam occurs in the gearbox.
Easy to change settings
Programming of all the settings is done solely by using quick and easily memorable sequences of fire selector switching and trigger pulls supported by sound signals and multicolor LED diode. The chip communicates with the user via beeps and a multicolored LED. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.
Perun for Krytac Kriss Vector works without problems with any battery from 7V do 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.